How to Read Two-wheeler Tyre Markings
TIPS & TRICKS
11
tyre-maintenance

Tyres are the only contact your two-wheeler has with the road while in motion. It is, thus, extremely important to ensure that the tyres installed on your two-wheeler are of the correct specification, or there may be some very undesirable consequences. For example, a tyre which is too wide, if installed on a commuter bike would reduce not just its acceleration and efficiency but also make it dynamically unstable despite having a wider contact patch. On the other hand, a slim tyre installed on a high performance machine would get shredded to bits before you know.

In order to ensure that the specification of a tyre could be clearly defined by a manufacturer, and understood by the end consumer, there’s a well defined nomenclature for tyres. All tyres made by credible manufacturers come clearly marked with codes denoting details about all the critical parameters defining their capability. In this guide we’ll tell you everything about how to read two-wheeler tyre markings, and why they are important.

Size, load and speed rating

Let’s take this tyre image as an example. The size, load and speed markings on the sidewall read 180 / 50 R17 71 W

Tyre width – the first two or three digits of the marking represent the section width in millimetres, measured from the widest parts of sidewall to sidewall (not the contact patch) with the tyre inflated to its correct specification. So the number 180 in our example represents a 180mm wide tyre. This is followed by a forward slash ‘/ ‘ for separating the next number.

Aspect Ratio or profile –  The next digits denote the aspect ratio. This represents the height of the sidewall or the ‘profile’ of the tyre. Aspect ratio is typically denoted as a percentage of the section width of the tyre. In our example it’s 50, which means that the height of the tyre’s sidewall is 50% of its nominal sectional width or less.

Tyre construction – Sometimes (but not in all cases) the aspect ratio is followed by a code indicating the construction type of the tyre. The code is represented by a letter from the alphabet, and this is what it means

  • B – bias belt or bias ply construction
  • D – Diagonal tyres made of nylon cords placed diagonally across each other in the tread and sidewall.
  • R – Radial tyres

Wheel diameter

The next set of digits represents the diameter of the wheel in inches. In our example it’s 17, which means that the tyre is meant for 17 inch wheels.

Load Index

The next set of digits represents the load index, which denotes the maximum mass, or weight the specific tyre could carry. Here’s a part of the load index table for reference. Some tyre makers also specify the maximum load a tyre can take separately in kg.

Load IndexLoad in kg
62265
63272
64280
65290
66300
67307
68315
69325
70335
71345
72355
73365
74375
75387

Speed rating

From slow moving mopeds to superbikes which could hit the triple ton mark, tyres are made for all varieties of two-wheelers. The fastest speed a tyre can travel at is denoted by the speed rating. Speed rating is indicated by either a single letter, a combination of a letter and a digit, or a letter in brackets. As in case of load, some manufacturers provided the speed limit of the tyre specifically in miles per hour (mph) or km/h separately.

Also Read: Tips to Keep Your Two-Wheeler Tyres in Good Health

The complete list of speed rating codes and their respective speeds is provided below:

Speed rating

Codemphkm/h
A135
A2610
A3915
A41220
A51625
A61930
A72235
A82540
B3150
C3760
D4065
E4370
F5080
G5690
J62100
K68110
L75120
M81130
N87140
P94150
Q100160
R106170
S112180
T118190
U124200
H130210
V149240
Zover 149over 240
W168270
(W)over 168over 270
Y186300
(Y)over 186over 300

Date of Manufacture

The date of manufacture of a tyre is typically enclosed in an oval and may be preceded by a code, which represents the facility where the tyre was manufactured. Last four digits of this code tell you the date of production of the tyre. The first two digits represent the week of the year when the tyre was produced from 1 to 52. The last two digits represent the year. So, basically a tyre marked 4513 was manufactured in the 45th week of 2013. This is a good way for consumers to ensure that the tyre they’re buying is not too old, as tyres turn hard over time and don’t perform optimally.

Also Read: TVS Apache RR310 Rider’s Guide: Using Dual Channel ABS Brakes Effectively

Other common markings

Direction of rotation – Represented by an arrow with the head denoting the direction of rotation

Air pressure – in some cases, the tyre will have explicit markings indicating the maximum pressure in PSI or kPA.  This isn’t necessarily provided on all tyres though.

TL – Tubeless

TT – Tube-type, this tyre must be used only with an inner tube

Made in ‘Country’: Depicts the country of manufacture

TWI: It’s the tyre Tread Wear Indicator which lets you know when the tread has worn out and the tyre needs replacement.


Leave your comment below:

Your email address will not be published. Required fields are marked *